Home > Tube Driver > Bk Butler Tube Driver Schematics

Bk Butler Tube Driver Schematics

Contents

TUBE DRIVER VERSIONS - There have been numerous version of the Tube Driver made since the 1980s, but these are all of the 4 knob versions. Butler had a firm in California manufacture a second circuit board for him sometime in 1987. If I plugged it into things like a mixer, the output was too low. It sounds like 50-60Hz noise or a ground loop hum. navigate here

He uses the TD for a slightly dirty clean tone in his live rig. Has anyone tried what happens with the 12AT7/ECC81 (like the original '80s) or 12AY7/6072A? However, this AC is 1.6 A RMS, and then tends to disturb the other signal tubes of the circuit, if it is not the screen. High volume settings can place a load on the Hi and Lo controls, so different volume levels can affect the output sound differently. http://revolutiondeux.blogspot.com/2012/02/b-k-butler-tube-driver.html

Baja Tube Driver

Tube Drivers can sound slightly different from each other anyway, primarily because of differences in the way different tubes filter the sound and circuit variations, but when using the exact same He ran out of them in 2006. Drill a hole and install a 1/8" power jack on the back of the enclosure. If the PT is close to the tube, that wont help.

Logged sgmezei Electron Doctor Posts: 895 Scott- AB, Canada Re: BK Butler Tube Driver « Reply #7 on: April 22, 2011, 06:55:28 PM » +1I just received a Baja real tube Shown above (left to right) - An original long-plate Ei Yugoslavian 12AX7 tube re-branded "TUBE DRIVER" that shipped with the original BKB/Chandler Tube Driver in 1986-87, the same tube branded "CHANDLER Reply With Quote 03-18-2012,11:06 PM #28 David Schwab Pickup Maker Join Date May 2006 Location Staten Island, NY Posts 10,919 Originally Posted by mozwell Hi Guys If you are building a Chandler Tube Driver I havent used a Butler, so i cant compare, but people on FSB have commented how much they like this newer version over the Butler one.

It does a great lead tone, although it does not have quite the same huge bottom end and scooped mid range you find in a Ram's Head era Big Muff. Bk Butler Tube Driver Review This is called a "starved plate" design, and you won't see much tube glow, if any, if you look inside. I can cop the perfect Jack Bruce tone with ease. http://www.kitrae.net/music/Music_mp3_Tube_Driver_Sound.html It only made a minor difference however.

I have a page about Gilmour's various Tube Drivers and settings HERE. What Is A Tube Driver It would be possible to describe everything scientifically, but it would make no sense; it would be without meaning, as if you described a Beethoven symphony as a variation of wave OVERDRIVE SETTING - Example of the Tube Driver overdrive setting with a Fender Strat into a Fender Twin Reverb. BUTLER TUBE DRIVER ©Kit Rae.

Bk Butler Tube Driver Review

Butler has always made these stock with 12AX7 tubes, but owners typically experiment with different tubes to tailor their tone. http://www.diystompboxes.com/smfforum/index.php?topic=16686.0 Last edited by David Schwab; 04-06-2012 at 09:33 PM. Baja Tube Driver This way I wouldn't need any particular power supply (except a good wall wart). Bk Butler Tube Driver Clone It is not very versatile sounding through some amps, but exceptionally good with others.

Logged Analogue Signal Processing finkfloyd member2 Posts: 221 Total likes: 0 dont give out personal info... check over here From your pedal you can understand how the resistor is placed from 100K? I have the Limiter set for pretty much unity gain. This tube works very well for players seeking a cleaner tone in the lower settings of the drive control. Tube Works Tube Driver

Why not try it on your Blue Tube the 12AY7? Reply With Quote Page 1 of 2 12 Last Jump to page: « Wanted: Opinion on using a tube preamp with a SS amp | Super Fuzz Flux Residue » Thread I was going for the Pulse era live tone here. his comment is here Very EJ-like even though I'm apparently not running it the way he does.

Logged Owner and operator of Magic Pedals Partner and production builder of Dunwich Amplification ckim715 Solder Ninja Posts: 249 Re: BK Butler Tube Driver « Reply #9 on: April 25, 2011, Chandler Tube Driver Rack LIGHT DRIVE / BOOST SETTING - Example of the Tube Driver light drive setting with a Fender Strat into a Reeves custom 50. What's New?

In 2006 Butler reissued the 911 Tube Driver by custom order through his Butler Audio company.

I still have the original tube. Butler called the 1970 'NOS' YUGO tubes, meaning "new old stock" tubes made in Yugoslavia in the 1970s. To have a cleaner, more vintage sound, you can substitute a 12AU7 tube, which will clean up the tone and thins out the midrange. Genz Benz Tube Driver PS - I heard/read that EJ has had the bias mod on his for a long time but...who knows.

The signal that goes on the grid is taken at the connection point between the two resistors. The various versions of the yellow capped knobs used on the older Tube Drivers were cheaply made and broke easily, and the the yellow caps were prone to falling off and Just remember to mount the 7812 to the case or to a small heat sink.I don't know about the noise from that product (I've only serviced one and it was years weblink I'm looking for a warm clean tone, not over drive.

Enable and reload.Sign inButler tube driver schematicsShareThis version of Firefox is no longer supported. The circuit layout and pathways were very similar to the 1980s circuits, but there were several component value changes across the circuit that affect the way it sounds. It would be possible to describe everything scientifically, but it would make no sense; it would be without meaning, as if you described a Beethoven symphony as a variation of wave BUTLER REAL TUBE OVERDRIVE - The Tube Driver is a booster/overdrive pedal with an IC and vacuum tube driven preamp circuit inside, used by guitarists such as David Gilmour of Pink




© Copyright 2017 pausesexe.com. All rights reserved.